Skip to main content

Meriwether Millworks

How We Make Our Charcuterie Boards

It starts with a fallen tree

We collect trees that have fallen during storms or were removed for a variety of reasons. We use a Wood-Mizer LT40Wide portable sawmill to mill up the logs.  Often the logs that yield the prettiest figure are rejected by your traditional sawmill.  Since we do not have to worry about meeting a certain production quota, we can take this odd logs (sometimes they have a significant curve) and take our time milling them to get the best wood out of them rather than letting them get hauled off to a landfill.  

Removing the water

When you first cut a log, it is loaded with water.  Depending on the species, water can make up 30 to 60% (possibly more) of the logs total weight.  The water must be removed before you can use the wood for furniture.  If you don't the wood will warp and twist after it is brought inside because of the changes in humidity.  We use a Wood-Mizer KD250 Dehumidification Kiln to remove the water from the wood. It can remove up to 250 pounds of water a day and dry the wood in just a few weeks instead of months or years.  The kiln cart, when fully loaded, can weigh up to 14,400 pounds (just over 7 tons)!  At the end of the drying cycle, the kiln super heats the wood to sterilize it and kill any insect eggs that may be in the wood.

Cutting and Flattening

Once the kiln had dried and sterilized the wood, we remove it and begin the laborious process of prepping each board.  Using our templates, we pick the best parts of the slabs to cut into boards.  Once they are cut, we have to flatten them out.  Often, wood moves when it dries depending on the stressors in the wood.  We remove 'cups' or 'twists' from the wood using a slab flattening mill.  

Rough Sanding

By this point, the boards are flat, but they have a lot of marks on them. In this step, we use heavy duty sanders and remove all the rough marks from the boards. We also carve off any bark because it often falls off anyways and we feel it detracts from the overall beauty of the board.

Dealing with soft spots

Allowing a log to start rotting can result in some stunning wood. Insects and fungus can create some beautiful colors and 'spalting.' Of course, you have to achieve a balance. If you allow it to sit too long, the wood just crumbles in your hands. If you stop it too soon, you don't quite get the result you want.  Even in the best circumstances, the result will leave some rotten areas. We do 1 of 2 things in this situation. We either reinforce the soft wood with epoxy, or we chisel out the rotten area and fill it with epoxy. This is a time consuming process but well worth it.

Finish Sanding

This part of the process can be tedious.  We start our progression through multiple 'grits' of sandpaper to achieve a smooth even finish.  It takes a fair amount of time on each board, but it is worth it.  This is when we spend lots of money on sandpaper and audio books (LOL)!

Prepping for Handles

Before applying the finish, we drill the holes for the handles.  We have a nice little template to properly place the holes, but the live edges create a slight irregularity.  This makes picking the right spot for the handles more of a creative process than a precise one.  We countersink the holes on the underside so the screws are not exposed.  

Applying the finish

There are two parts to the finish.  The first is the application is a food safe finish called Walrus Oil.  Walrus fat makes an amazing finish.  Just kidding.  No Walrus's were harmed in the finishing of these boards.  Walrus oil is just the name of the brand we use and love.  We let the finish soak in for 12-24 hours.  Then we apply a layer of wax from the same company.  While the finishing process has the potential to be tedious, we really enjoy it because that is when you see the grain and color in the wood really pop!  Each board is something new and we love it.  Once we have waxed the boards, we attach the handles.  Now all that is left is to build the boxes.